A Tank Tee is 1/4 inch compression fitting with multiple connections and item ports, when used the installation is neat and lightweight. The two main line connections, one for the inlet supply line from the pump / well, one other connects to the discharge line to the plumbing system. Four FPT item ports for any pressure switch, pressure gauge, relief device and drain valve eliminate the need for having multiple fittings and nipples which include mess around a pressure tank.

Kinds of Tank Tees

Tank tees are available in various lengths brief (3”) to long (16”) to work using the connection dimensions and locations on various brand names of pressure tanks. Both major style kinds are Union and Non-union which may be known as strong or 1-piece tank tees. They are available in 1” and 1-¼” with male or female tank contacts. Regardless tank tees are equipped for connecting to any pre-charged pressure tanks. Tank tee length measurements are Middle-End-Lengths (CEL)

Are used on pressure tanks with all the tank connection protruding from the part of the tanks base. Brief tees range from 3” to 4-1/2” CEL. Short tank tees can be purchased in various kinds tank link as demonstrated below.

Long Tees Tank

Are used on stress tanks using the tank connection being either in the center or counteract within the foot of the tanks base. Long tanks tees have male NPT tank connection and are available in several measures. For a longer time tank tees are essential since the size from the stress tank selected increases, the CEL must be sufficient to prolong the tee head out far sufficient so that the pressure switch can threaded on or away without having getting in touch with pressure tank. Diagram, engineering drawing

Union vs. Non-Union Tank Tees

Some great benefits of union tank tees are realized during preliminary installation, and considerably decreases the work included for tank substitute. A union type tee easily disconnects the existing tank, which can be eliminated within a few minutes departing each of the line and accessory contacts and wires intact. The newest tank can then be installed with all the tank tee lower leg from your aged tank, set constantly in place and reconnected towards the tank tee head by tightening up the union. Task finished!

Union tees that incorporate an O-diamond ring provide a dependable watertight seal. No need to worry about the link seeping. It is strongly recommended to select a quality tank tee which uses a Northern United states standard O-diamond ring which are plentiful in case a substitute is actually required.

Non-union tank tees perform the exact same job, are less money and spend less on the investment price. However, they just do not possess the same easy set up and time saving advantages especially when a tank needs to be changed. The additional labor included during installation or tank replacement will significantly surpass the first savings around the tee.

Stainless-steel Tank Tees

Stainless-steel tank tees more price aggressive than No-Lead Bronze and are changing bronze (red brass) tank tees because the creation of No-Lead requirements in 2014. Typically cast from 304 stainless which can be incredibly durable and incredibly corrosion resistant. Even though stainless steel tees can be more expensive than brass, they actually do not contain zinc alleviating the issues with dezincification that can happen when utilizing brass alloy tank tees in aggressive water problems. An additional benefit is definitely the extremely high strength of stainless-steel practically removes all risk of stress cracking when threading into female connections.

Brass Alloy Tank Tees

Brass tank tees are less costly and therefore are best for installs in many locations. However brass alloys2-07TK-25SF-2NL usually are not as corrosion resistant as stainless steel, therefore installs in places that the water is highly corrosive to brass, it is recommended to update to stainless.

Galvanized Tank Tees

Galvanized tees are cheaper than each stainless-steel and brass tank tees. Their use is typically07HC125G restricted to installations on galvanized stress tanks with no bladder. Galvanized tees are chosen to eliminate the risk of galvanic corrosion among dissimilar precious metals. Galvanized tank tees used in conjunction with galvanized nipple and fittings lgotli the issue. It is important to note that some plumbing rules do not let the usage of galvanized fixtures and nipples, one should verify that galvanized tank tees meet each of the applicable plumbing code requirements.

Pvc material Tank Tees

PVC tank tees are a very aggressive option in comparison to stainless, brass, and07PT-25-2 galvanized components. They are extremely resistant to rust, they may not be as durable as metal tank tees, nor are there numerous configurations readily available. They may be a really appropriate option, when proper PVC set up methods are followed, utilizing a high-high quality thread sealant mixture rather than PTFE thread sealant adhesive tape and avoiding over tightening up will reduce the risk of more than stressing the female NPT item plug-ins.

1 2 Inch Tee Fitting..

We are using cookies on our website

Please confirm, if you accept our tracking cookies. You can also decline the tracking, so you can continue to visit our website without any data sent to third party services.